The Way To Restore Vintage Or Old Furniture

The Way To Restore Vintage Or Old Furniture

You may simply transform a chunk of furniture cheaply by stripping off the old paint and refinishing the wood as to its unique state. By stripping old furniture down to the natural wood you'll be able to guarantee a smooth surface - free of bumps and blemishes - which may be polished, varnished and even stenciled for a completely new look. Make positive first that you just know what finish you are stripping because, paint, polish, lacquer or varnish all require different treatments.

Equipment: By hand, you want paint stripper, liquid or jelly kind, methylated spirits, and turpentine. A pair of rubber gloves, old paint brush 25 - 50 mm wide, a scraper, course wire wool and sand paper fine to medium grade.

Paint Stripping: if you are professional for tough work it can be removed by immersing the article in a caustic bath. A safer suggestion I'd suggest by hand, utilizing a chemical paint stripper; this gives great outcomes as it adds an additional luster to the bare wood.

Methodology: Firstly make sure that your work area is well ventilated as paint stripper provides off disagreeable fumes. Remove all fittings handles, key guides and so forth, then start brushing the stripper on to the painted areas, work the stripper into all cracks/crevices. When you could have covered a workable space, depart the stripper to act for several minutes. When it starts to bubble, remove the paint layer with your stripping knife or scraper, (put the paint shreds into an old paint tin as being caustic they're harmful) repeat the process till you reach the wood. When all the paint has been stripped, subsequent step is to scrub the wood down with the manufactures recommendation on what neutralizer to make use of this will remove any remaining debris on the identical time neutralizes the stripper. If the recommended neutralizer is say turpentine then soak a ball of wire wool and thoroughly rub down the stripped surface. When dry sandpaper down to a smooth finish. Necessary; always rub within the direction of the grain.

Stripping polish: before you can remove successfully, you need to know firstly the type of polish. If it is French polish this could be removed quite simply with methylated spirits, wipe it on generously, leave for a few minutes. When the polish has softened, scrape it off with a scraper then with fine wire wool (soaked in Methylated spirits) when the wood is dry you'll be able to sandpaper down to a pleasant smooth finish. If it is a Wax polish (oily surface) this you'll be able to remove with fine steel wool soaked with turpentine. Repeat until you're at the bare wood, dry off with an absorbent cloth.

Varnished and Lacquered finishes: if the article being 50 years or more old it probably is an oil based varnish of which was made from resins dissolved in oils and solvents. The cleanest/easiest way is with a scraper; tilt the scraper away from you working alongside the grain (by no means across the grain). Polyurethane varnishes use a paint stripper. Cellulose-primarily based varnishes could be removed by paint stripper, acetone, cellulose thinners, ammonia caustic soda, or turpentine. Counsel test a small area first to see which works best. Repairs, now you might be able to see the varied faults. Your repairs are mandatory earlier than the new finish can be applied, perhaps the draws require re-nailing or weak joints to be glued, cracks and holes must be filled. Minor cracks and holes you utilize a plastic wood or non-shrinking stopper all available in numerous natural wood colors. Massive holes must be Plugged with a similar wood, reduce to shape making positive the grain of the pug runs the same way as the rest of the surface, and then glue it in. Fine sandpaper all of your repairs down to a smooth finish for the subsequent stage.

Finishing with polyurethane: this gives bare wood a lustrous, hard wearing end of which is easy to clean and maintain. Polyurethane can withstand heat without marking though intense heat will damage the wood. There may be quite a lot of natural wood colors available as well as clear all matt or gloss finish. You will need to let Polyurethane set; some brands can take as much as two weeks to achieve maximum hardness. Apply the varnish directly to the sanded wood with a brush because the varnish must be utilized in coats. It's a good idea with the primary coat to dilute with spirit so that it soaks in and seals the wood. After each subsequent coat (when dry) lightly rub down with a fine sand paper. In case you are using one of many colored varieties it would pay you to apply the primary coat with a clear, this will save any likelihood of a patchy finish. If you would like a matt finish after utilizing colored varnish make the ultimate coat with a clear matt.